New D170 Loader

Utility Loaders
REQUEST A QUOTE
REQUEST A QUOTE
Key Features
  • Compatible with 4M and 4R Series Tractors
  • Rigid mounted with parking kit available
  • Easy maintenance points keeps you on the job
  • 1,760 pounds (800 kg) lift capacity

More Info

Features

End-of-pin lubrication means easy maintenance
Close up of grease fittingClose up of grease fitting
Pivot point grease fitting locations (400X shown)Pivot point grease fitting locations (400X shown)

All pivot points on the loader have grease fittings that are accessible from the side of the loader to make greasing the loader much easier, ensuring that all grease points are more likely to be serviced.  No more searching for grease points that are hard to find.  Removing the grease gun from the grease fitting is not a problem as sufficient radius has been left to allow the grease gun tip to be rotated to the side for removal from the fitting.

Specifications

Compare >>>

Select up to 2 models to compare specifications

John DeereD170 Loader
Add Model
Add Model
Tractor
Model 4044M, 4049M, 4052M, 4066M and OOS: 4044R, 4049R, 4052R, 4066R
Front tire 25x10-16.5 4PR R4
Rear tire 16.9-24 4PR
Front axle configuration
Wheelbase 73 in.
1850 mm
Pump capacity 10.2 gpm
Rated pressure 2500 psi
Loader
Leveling configuration
Bucket used Materials
Bucket weight 238 lb
108 kg
Lift capacity at full height Measured at pivot (U)
2391 lb
1087 kgMeasured at 500 mm ahead of pivot (V)
1760 lb
800 kg
Lift capacity at 59 in. (1500 mm) Measured at pivot (W)
2875 lb
1307 kgMeasured at 500 mm ahead of pivot (X)
2295 lb
1043 kg
Boom breakout force Measured at pivot (Y)
3853 lbf
1743.7 kgfMeasured at 500 mm ahead of pivot (Z)
2902 lbf
1315.4 kgf
Bucket rollback force capacity At maximum height (VV)
4112 lbf
1866.1 kgfAt 59-in. (1500-mm) lift height (XX)
5191 lbf
2355.1 kgfAt ground-level line (ZZ)
3487 lbf
1580.6 kgf
Dimensions Maximum lift height (A)
112.1 in.
2850 mmAt full height - bucket level(B)
104.1 in.
2646 mmAt full height - bucket dumped (C)
90.4 in.
2298 mm
Overall length (I+F), ft (m) 11.5 ft
3.522 m
Overall height in carry position (J) 4.94 ft
1.5 m
Digging depth (H) -5.7 in.
-146 mm
Reach At maximum height (D)
27.7 in.
705 mmAt ground level - bucket level (F)
65.8 in.
1672 mm
Bucket angle Dump angle, degrees (E)
42 degree (angle)Rollback angle, degrees (G)
28.6 degree (angle)Dump angle, ground
128.2 degree (angle)
Cycle times Loader raise, seconds
4.26 secondsLoader lower, seconds
3.13 secondsBucket dump, seconds
3.14 secondsBucket rollback, seconds
2.42 seconds

Accessories and Attachments

Buckets

61 In. (1550 mm) Loader Heavy Duty Bucket with Holes for Cutting Edge - BW14764
Heavy-duty bucketsHeavy-duty buckets

Heavy-duty buckets are available for tasks requiring more robust bucket designs. Recommended for heavier use applications, such as commercial operations.

 

Top surface of the bucket is parallel to the cutting edge, which aids operator as a leveling guide.

 

Additional strength is built into the bucket design with additional wear bars, boxed top bucket section, and bucket end plate supports.

 

Cutting edge has pre-drilled holes for addition of a replaceable cutting edge.

61 In. (1550mm) Loader Materials Bucket - BW15863
Materials bucketMaterials bucket

Materials buckets are available to match tractor and loader applications.

 

May be used for loading dirt, gravel, feed, and light materials as well as scraping, digging, and other general purpose tasks.

 

IMPORTANT: Materials buckets are not recommended for heavy-duty tasks. For heavier use applications, use heavy-duty bucket.

 

Top surface of the bucket is parallel to cutting edge, which aids operator as a leveling guide.

 

Quik-Change connection for easy on and off.

 

Round-back design helps material flow when filling or dumping the bucket.

61 In. (1550mm) Loader Materials Bucket - Quik Change - BW14146
73 In. (1850 mm) Loader Heavy Duty Bucket with Holes for Cutting Edge - BW14765
73 In. (1850 mm) Loader High Volume Bucket - BW14658
73 In. (1850 mm) Materials Bucket - BW16183
Materials bucketsMaterials buckets

Materials buckets are available to match tractor and loader applications. May be used for loading dirt, gravel, feed and light materials, as well as scrapping, digging and other general purpose tasks.

 

IMPORTANT: Materials buckets are not recommended for heavy-duty tasks. For heavier-use applications, use the heavy-duty bucket.

 

Top surface of the bucket is parallel to cutting edge, which aids operator as a leveling guide.

Quik-Change connection for easy on and off.

 

Round-back design helps material flow when filling or dumping the bucket.

85 In. (2150 mm) Loader High Volume Bucket - BW15273

Cutting Edges

61 In. (1550 mm) Replaceable Bucket Cutting Edge with Hardware - BW14762
73 In. (1850 mm) Replaceable Bucket Cutting Edge with Hardware - BW14763

HITCH ADAPTERS

iMatch Bushing Kit - BW15056

Hood Guards

Deluxe Brush Guard Attachment - BW16989
Deluxe Hood Guard Attachment - BW16155
Hood Guard - BW16335
Hood guard for 4R Series TractorsHood guard for 4R Series Tractors

A hood guard can be ordered for a tractor without ordering a loader.

 

The hood guard protects the front of the tractor while operating the loader.

 

The bolt-on design stays with tractor when loader is removed.

Hydraulics

3rd Function hydraulic lines and hoses - BW16448
BW16448 for D170 Loaders on 4M TractorsBW16448 for D170 Loaders on 4M Tractors

BW16448 provides metal lines along boom and flexible hydraulic hoses to connect to loader valve on mast assembly.

 

NOTE: Tractor third electrohydraulic (EH) valve kits will be needed. See tractor hydraulics for ordering.

BW16491 for D170 Loaders on 4R TractorsBW16491 for D170 Loaders on 4R Tractors

BW16491 provides metal lines along boom and flexible hydraulic hoses to connect to tractor mid-valve location.

 

NOTE: Tractor dual mid-valve and third EH valve kits will be needed. See tractor hydraulics for ordering.

3rd Function hydraulic lines and hoses - BW16491
BW16448 for D170 Loaders on 4M TractorsBW16448 for D170 Loaders on 4M Tractors

BW16448 provides metal lines along boom and flexible hydraulic hoses to connect to loader valve on mast assembly.

 

NOTE: Tractor third electrohydraulic (EH) valve kits will be needed. See tractor hydraulics for ordering.

BW16491 for D170 Loaders on 4R TractorsBW16491 for D170 Loaders on 4R Tractors

BW16491 provides metal lines along boom and flexible hydraulic hoses to connect to tractor mid-valve location.

 

NOTE: Tractor dual mid-valve and third EH valve kits will be needed. See tractor hydraulics for ordering.

Two Function Single Lever Control - for 400E and 4M tractor compatibility - BLV10878

Miscellaneous

Parking Stand Kit - BW16127

With BW15872 parking stand kit, the D160 Loader can now be quickly and easily removed from the tractor without tools.

The BW16127 parking stand kit allows for the D170 Loader to be parked from the tractor.

 

Instructions for attaching the loader

 

Instructions for detaching the loader

 

The kit includes the following:

  • Parking stands
  • Handled pins
  • Hydraulic hoses
  • Quick-couplers
  • Mounting bracket and hardware
Parking stand installedParking stand installed
Quick disconnect hydraulics’ connectedQuick disconnect hydraulics’ connected
Boom pins installedBoom pins installed

Tooth Bars

61 In. (1550 mm) Tooth Bar for Bucket - BW15227
Tooth barTooth bar

The tooth bar helps penetrate hard-packed material.  It attaches to the bucket by sliding over the cutting edge and is retained by two bolts, one in each end plate of the bucket.

  • Holes must be drilled in bucket end plates to retain the tooth bar
  • Protrudes beyond bucket edge approximately 150 mm or 6 in.
  • Recommended for use with heavy-duty buckets only
  • Not compatible with buckets with replaceable cutting edge installed
73 In. (1850 mm) Tooth Bar for Bucket - BW15228
Tooth barTooth bar

The tooth bar helps penetrate hard-packed material.  It attaches to the bucket by sliding over the cutting edge and is retained by two bolts, one in each end plate of the bucket.

  • Holes must be drilled in bucket end plates to retain the tooth bar
  • Protrudes beyond bucket edge approximately 150 mm or 6 in.
  • Recommended for use with heavy-duty buckets only
  • Not compatible with buckets with replaceable cutting edge installed